DESEN TEHNIC ŞI INFOGRAFICĂ III

H.Min.Sec.

CAPITOLUL 1 – INTRODUCERE 1h 38’ 14”

          1.        ISTORIC………………………………………………………………………………….

          2.        PRODUSE AUTODESK GRATUITE………………………………………………….

          3.        CERINTE SISTEM SI INSTALARE…………………………………………………...

          4.        ECRAN DE START………………………………………………………………………

          5.        APPLICATION OPTION………………………………………………………………..

          6.        CREATE NEW FILE…………………………………………………………………….

          7.        DESCRIERE INTERFATA………………………………………………………………

          8.        APLICATIE – FURCA + 3D Sketch…………………………………………………….

CAPITOLUL 2 – SKETCH / CREATE / PG / MODIFY – 1h 41’ 00”

          9.        RECAPITULAREA CAPITOLULUI ANTERIOR…………………………………….

      10.        SKETCH / START 2D SKETCH………………………………………………………..

      11.        2D SKETCH / CREATE………………………………………………………………….

a)      LINE, SPLINE (CONTROL VERTEX, INTERPOLATION), ECUATION CURVE, BRIDGE CURVE…………………………………………………………………………

b)      CIRCLE (CENTER POINT, TANGENT, ELLIPSE)……………………………………

c)      ARC (THREE POINT, TANGENT, CENTER POINT)…………………………………

d)      CREATE BLOCK, PRECISE INPUT…………………………………………………

e)      RECTANGLE (TWO POINT, THREE POINT, TWO PINT CENTER, THREE POINT CENTER),  SLOT (CENTER TO CENTE, OVERALL,, CENTER POINT, THREE POINT ARC, CENTER POINT ARC), POLYGON ………………………………

f)       FILET/CHAMFER…………………………………………………………………...      

g)      TEXT, GEOMETRY TEXT…………………………………………………………

h)      POINT…………………………………………………………………………………

      12.        2D SKETCH / PROJECT GEOMETRY……………………………………………

a.       PROJECT CUT EDGES………………………………………………………………

b.      PROJECT TO 3D SKETCH…………………………………………………………

c.       PROJECT DWG GEOMETRY……………………………………………………….

      13.        2D SKETCH / MODIFY……………………………………………………………….

a)      MOVE………………………………………………………………………………….

b)      COPY…………………………………………………………………………………...

c)      ROTATE………………………………………………………………………………..

d)      SCALE…………………………………………………………………………………

e)      STRETCH………………………………………………………………………………

f)       OFFSET………………………………………………………………………………...

g)      TRIM…………………………………………………………………………………...

h)      EXTEND……………………………………………………………………………….

i)        SPLIT…………………………………………………………………………………...

      14.        APLICATIE – RACORD CU FLANSA ………………………………………………

CAPITOLUL 3 - 2D SKETCH / 3D SKETCH – 1h 47’ 00”

      15.        RECAPITULAREA CAPITOLULUI ANTERIOR………………………………..

      16.        2D SKETCH / PATTERN……………………………………………………………

a)      RECTANGULAR…………………………………………………………………….

b)      CIRCULAR………………………………………………………………………….

c)      MIRROR………………………………………………………………………………

      17.        2D SKETCH / CONSTRAIN…………………………………………………………

a)      DIMENSION………………………………………………………………………….

b)      AUTO DIMENSION AND CONSTRAINTS………………………………………..

c)      SHOW CONSTRAINTS………………………………………………………………

d)      CONSTRAIN SETTINGS…………………………………………………………….

e)      COINCIDENT, COLINEAR, CONCENTRIC, FIX. PARALLEL, PERPENDICULAR, HORIZONTAL CONSTRAINT, VERTICAL, TANGENT, SMOOTH, SIMMETRIC, EQUAL………………………………………………………………………………..

f)       CONSTRAINT INTERFERENCE SCOP…………………………………………….

g)      EDIT COORDINATE SYSTEM…………………………………………………….

      18.        2D SKETCH / INSERT (IMAGE, POINTS, ACAD)……………………………….

      19.        2D SKETCH / FORMAT (CONSTRUCTION, DRIVEN DIMENSION, CENTERLINE, CENTER POINT,  SHOW FORMAT)…………………………….

      20.        SKETCH / START 3D SKETCH………………………………………………………

      21.        START 3D SKETCH / DRAW…………………………………………………………

a)      LINE……………………………………………………………………………………...

b)      HELICAL CURVE……………………………………………………………………….

c)      ARC (THREE POINT, CENTER POINT)……………………………………………….

d)      SPLINE (CONTROL VERTEX, INTERPOLATION)…………………………………..

e)      ECUATION CURVE, POINT, BEND……………………………………………………

f)       INTERSECTION CURVE……………………………………………………………….

g)      SILHOUETE CURVE…………………………………………………………………….

h)      PROJECT TO SURFACE…………………………………………………………………

i)        CURVE ON FACE……………………………………………………………………….

      22.        START 3D SKETCH / INCLUDE GEORMETRY……………………………………

      23.        START 3D SKETCH / CONSTRAIN…………………………………………………

a)      DIMENSION……………………………………………………………………………..

b)      SHOW CONSTRAINTS………………………………………………………………….

c)      COINCIDENT, COLINEAR, ON FACE, FIX, EQUAL PARALLEL, PERPENDICULAR, PARALLEL WITH X/Y/Z/ AXIS, TANGENT, SMOOTH, PARALLEL WITH XY/YZ/XZ PLANE……………………………………………………………………….

      24.        START 3D SKETCH / PATTERN – MIRROR………………………………………..

      25.        START 3D SKETCH / MODIFY………………………………………………………..

a)      3D TRANSFORM…………………………………………………………………………

b)      TRIM, EXTEND, SPLIT, INSERT POINT, INSERT ACAD…………………………….

      26.        START 3D SKETCH / INSERT, FORMAT……………………………………………

      27.        APLICATIE – PIESA CU FLANSA COMPLEXA…………………………………….

CAPITOLUL 4 -  3D MODEL / CREATE FEATURES – 1h 51’ 21”

      28.        RECAPITULAREA CAPITOLULUI ANTERIOR……………………………………

      29.        3D MODEL / CREATE FEATURES…………………………………………………….

a)      EXTRUDE………………………………………………………………………………….

b)      REVOLVE………………………………………………………………………………….

c)      SWEEP……………………………………………………………………………………..

d)      LOFT……………………………………………………………………………………….

e)      COIL………………………………………………………………………………………..

f)       EMBOSS……………………………………………………………………………………

g)      DERIVE…………………………………………………………………………………….

h)      RIB………………………………………………………………………………………….

i)        DECAL……………………………………………………………………………………..

j)        IMPORT…………………………………………………………………………………….

      30.        APLICATIE – PIESA SWEEP……………………………………………………………

CAPITOLUL 5 -  3D MODEL /  MODIFY – 1h 55’ 20”

      31.        RECAPITULAREA CAPITOLULUI ANTERIOR…………………………………

      32.        3D MODEL / MODIFY…………………………………………………………………

a)      HOLE…………………………………………………………………………………….

b)      FILLET……………………………………………………………………………………

c)      CHAMFER…………………………………………………………………………..........

d)      SHELL…………………………………………………………………………………….

e)      DRAFT…………………………………………………………………………………….

f)       THREAD…………………………………………………………………………………..

g)      COMBINE…………………………………………………………………………………

h)      THICKEN/OFFSET……………………………………………………………………….

i)        SPLIT……………………………………………………………………………………..

j)        DIRECT…………………………………………………………………………………..

k)      DELETE FACE…………………………………………………………………………..

l)        MOVE BODIES………………………………………………………………………….

m)    BEND PART…………………………………………………………………………….

n)      COPY OBJECT………………………………………………………………………….

      33.        APLICATIE – „HOLE COUNTERSINK”……………………………………………..

CAPITOLUL 6 – 3D MODEL /  WORK FEATURES / PATTERN – 1h 34’ 45”

      34.        RECAPITULAREA CAPITOLULUI ANTERIOR………………………………..

      35.        3D MODEL / WORK FEATURES…………………………………………………..

35.a           POINT…………………………………………………………………………......

1.      POINT……………………………………………………………………..........

2.      GROUNDED POINT……………………………………………………………

3.      ON VERTEX, SKETCH POINT, OR MIDPOINT…………………………….

4.      INTERSECTION OF THREE PLANES………………………………………..

5.      INTERSECTION OF TWO LINES……………………………………………..

6.      INTERSECTION OF PLANE /SURFACE AND LINE…………………………

7.      CENTER POINT OF LOOP OF EDGES………………………………………..

8.      CENTER POINT OF TORUS……………………………………………………

9.      CENTER POINT OF SPHERE…………………………………………………...

35.b           AXIS…………………………………………………………………………………

1.      AXIS………………………………………………………………………... .......

2.      ON LINE OR EDGE…………………………………………………………….

3.      PARALLEL TO LINE THROUGH POINT……………………………………..

4.      THROUGH TWO POINT……………………………………………………….

5.      INTERSECTION OF TWO PLANES……………………………………………

6.      NORMAL TO PLANE THROUGH POINT……………………………………..

7.      THROUGH CENTER OF CIRCULAR OR ELLIPTICAL EDGE………………

8.      THROUGH REVOLVED FACE OR FEATURE………………………………..

35.c           PLANE……………………………………………………………………………..

1.      PLANE……………………………………………………………………………

2.      OFFSET FROM PLANE…………………………………………………………

3.      PARALLEL TO PLANE THROUGH POINT……………………………………

4.      MIDPLANE BETWEEN  TWO PLANES………………………………………

5.      MIDPLANE OF TORUS………………………………………………………….

6.      ANGLE TO PLANE AROUND EDGE…………………………………………..

7.      THREE POINTS…………………………………………………………………..

8.      TWO COPLANAR EDGE………………………………………………………..

9.      TANGENT TO SURFACE THROUGH EDGE………………………………….

10.  TANGENT TO SURFACE THROUGH POINT…………………………………

11.  TANGENT TO SURFACE AND PARALLEL TO PLANE……………………..

12.  NORMAL TO AXIS THROUGH POINT………………………………………..

13.  NORMAL TO CURVE AT POINT………………………………………………

35.d             USER COORDONATE SYSTEM……….............................................................

      36.        3D MODEL / PATTERN………………………………………………………………

a)      SKETCH DRIVEN…………………………………………………………………….

b)      CIRCULAR PATTERN……………………………………………………………….

c)      RECTANGULAR PATTERN…………………………………………………………

d)      MIRROR……………………………………………………………………………….

      37.        APLICATIE – TANGENT TO SURFACE……………………………………………

CAPITOLUL 7 – 3D MODEL / SURFACE SI FREEFORM – 1h 47’ 50”

      38.        RECAPITULAREA CAPITOLULUI ANTERIOR………………………………..

      39.        3D MODEL / SURFACE…………………………………………………………….

a)      RULED SURFACE…………………………………………………………………

b)      PATCH………………………………………………………………………………

c)      EXTEND…………………………………………………………………………….

d)      STITCH………………………………………………………………………………

e)      TRIM…………………………………………………………………………………

f)       REPLACE FACE…………………………………………………………………….

g)      SCULPT………………………………………………………………………………

h)      REPAIR BADIES……………………………………………………………………..

      40.        APLICATIE SUPRAFETE ………………………………………………………….

      41.        3D MODEL / CREATE FREFORM…………………………………………………

a)      FACE………………………………………………………………………………….

b)      CONVERT……………………………………………………………………………

c)      BOX + EDIT FREEFORM…………………………………………………………..

d)      PLANE+ EDIT FREEFORM ………………………………………………………..

e)      CYLINDER+ EDIT FREEFORM ..…………………………………………………

f)       SPHERE+ EDIT FREEFORM .…………………………………………………….

g)      TORUS+ EDIT FREEFORM ………………………………………………………..

h)      QUADBALL………………………………………………………………………….

      42.        3D MODEL / CREATE FREFORM  /EDIT ……………………………………….

a)      ALIGN FORM………………………………………………………………………..

b)      COMBINE + FILET ………………………………………………………………….

c)      DELETE FREEFORM……………………………………………………………….

d)      SUBDIVIDE…………………………………………………………………………..

e)      INSERT EDGE………………………………………………………………………..

f)       BRIDGE……………………………………………………………………………….

g)      MIRROR………………………………………………………………………………

h)      TOGGLE SMOOTH…………………………………………………………………..

i)        TOGGLE TRANSLUCENT…………………………………………………………..

      43.        APLICATIE FREEFORM – BIDON…………………………………………………

CAPITOLUL 8 – INDICATOARE INTELIGENTE SI DESEN DE EXECUTIE

 1h 48’ 41”

      44.        RECAPITULAREA CAPITOLULUI ANTERIOR………………………………..

      45.        CREATE NEW FILE „ISO.IDW”…………………………………………………..

      46.        SHEET:1……………………………………………………………………………….

      47.        DRAWING RESURCES………………………………………………………………

a)      TITLE BLOCKS………………………………………………………………………

b)      BORDERS…………………………………………………………………………….

c)      SHEET FORMATS……………………………………………………………………

      48.        FILE \ iProperties………………………………………………………………………

      49.        SHEET:1 \ BDM ISO \ Edit Definition……………………………………………….

      50.        SHEET:1 \ BDM ISO \ Delete.......................................................................................

      51.        BDM BORDERS \ Define New Zone Border…………………………………………

      52.        BDM Title Blocks \ Define New Title Block………………………………………….

      53.        DESENARE INDICATOR CU SIGLA……………………………………………….

      54.        INSERARE INDICATOR  AUTOCAD……………………………………………….

      55.        INDICATOR INTELIGENT…………………………………………………………..

      56.        COPIERE PERSONALIZARE IN TEMPLATES…………………………………..

      57.        APLICATIE 2D CU MODIFICARI DE PROPRIETATI…………………………..

CAPITOLUL 9 – DESENE DE EXECUTIE „ISO.IDW” – 1h 58’ 20”

      58.        RECAPITULAREA CAPITOLULUI ANTERIOR…………………………………

      59.        „ISO.IDW” / PLACE VIEW / CREATE……………………………………………..

a)      PLACE VIEW………………………………………………………………………….

b)      BASE……………………………………………………………………………………

c)      PROJECTED……………………………………………………………………………

d)      AUXILIARY……………………………………………………………………………

e)      SECTION……………………………………………………………………………….

f)       DETAIL…………………………………………………………………………………

      60.        „ISO.IDW” / PLACE VIEW /  DRAFT……………………………………………….

      61.        „ISO.IDW” / PLACE VIEW / MODIFY……………………………………………….

a)      BREAK…………………………………………………………………………………...

b)      BREAK AUT…………………………………………………………………………….

c)      SLICE…………………………………………………………………………………….

d)      CROP…………………………………………………………………………………….

      62.        „ISO.IDW” / PLACE VIEW / ALIGNMENT................................................................

a)      BREAK ALIGNMENT………………………………………………………………….

b)      ORIZONTAL…………………………………………………………………………….

c)      VERTICAL………………………………………………………………………………

d)      IN POSITION……………………………………………………………………………

      63.        „ISO.IDW” / PLACE VIEW / SKETCH\START SKETCH……………………….....

      64.        „ISO.IDW” / PLACE VIEW / SHEET\NEW SHEET…………………………………

      65.        APLICATIE – OBTINEREA PROIECTIILOR……………………………………….

      66.        „ISO.IDW” / ANNOTATE ………………………………………………………………

a)      DIMENSION……………………………………………………………………………..

b)      BASELINE (Baseline, Baseline Set)…………………………………………………….

c)      ORDINATE (Ordinate, Ordinate Set)……………………………………………………

d)      CHAIN (Chain, Chain Set)………………………………………………………………

e)      ARRANGE………………………………………………………………………………

      67.        „ISO.IDW” / ANNOTATE  / FEATURES NOTES……………………………………

a)      HOLE AND THREAD………………………………………………………………….

b)      CHAMFER………………………………………………………………………………

c)      PUNCH………………………………………………………………………………….

d)      BEND……………………………………………………………………………………

      68.        „ISO.IDW” / ANNOTATE  / TEXT……………………………………………………

a)      TEXT……………………………………………………………………………………

b)      LEADER TEXT………………………………………………………………………..

      69.        „ISO.IDW” / ANNOTATE  / SYMBOLS……………………………………………..

      70.        DEFINE NEW SYMBOL……………………………………………………………….

      71.        INSERT SKETCH SYMBOL………………………………………………………….

      72.        SYMBOLS……………………………………………………………………………….

a)      SURFACE………………………………………………………………………………

b)      WELDING………………………………………………………………………………

c)      CATERPILAR………………………………………………………………………….

d)      END FILL………………………………………………………………………………

e)      FEATURE CONTROL FRAME………………………………………………………

f)       DATUM IDENTIFIER SYMBOL…………………………………………………….

g)      FEATURE IDENTIFIER SYMBOL…………………………………………………..

h)      CENTER LINE…………………………………………………………………………

i)        CENTERLINE BISECTOR……………………………………………………………

j)        CENTER MARK……………………………………………………………………….

k)      CENTERED PATTERN……………………………………………………………….

      73.        ISO.IDW” / ANNOTATE  / RETRIEVE……………………………………………...

      74.        ISO.IDW” / ANNOTATE  / SKETCH / START SKETCH………………………….

      75.        ISO.IDW” / ANNOTATE  / TABLE…………………………………………………...

a)      PART LIST………………………………………………………………………………

b)      HOLE (Hole Selection, Hole View, Hole Feature)………………………………………

c)      REVISION (Revision, Revision Tag)……………………………………………………

      76.        ISO.IDW” / ANNOTATE  / BALLOON (Auto Balloon)………………………………

      77.        ISO.IDW” / ANNOTATE  / EDIT LAYER…………………………………………….

      78.        ISO.IDW” / ANNOTATE  / FORMAT………………………………………………….

CAPITOLUL 10 – TRUCURI FINE – 2h 02’ 41”

      79.        RECAPITULAREA CAPITOLULUI ANTERIOR…………………………………

      80.        FILE/iPROPERTIES………………………………………………………………….

      81.        TOOLS/DOCUMENTS SETTINGS…………………………………………………

      82.        ANNOTATE/DIMENSION…………………………………………………………..

      83.        ANNOTATE/HOLE+THREAD NOTE……………………………………………...

      84.        ANNOTATE/TOLERANCE FEATURE……………………………………………

      85.        ANNOTATE/DRF……………………………………………………………………..

      86.        ANNOTATE/TOLERANCE ADVIZOR…………………………………………….

      87.        ANNOTATE/SURFACE TEXTURE……………………………………………….

      88.        ANNOTATE/LEADER TEXT……………………………………………………….

      89.        ANNOTATE/GENERAL NOTE…………………………………………………….

      90.        ANNOTATE/GENERAL PROFILE NOTE………………………………………..

      91.        ANNOTATE/MANAGE……………………………………………………………..

      92.        ANNOTATE/3D PDF………………………………………………………………..

      93.        ISO.IDW” / BDM VIEW  / RETRIEVE MODEL ADNOTATION……………

      94.        ANNOTATE/CAD FORMAT……………………………………………………….

      95.        INSPECT/MEASURE………………………………………………………………..

      96.        INSPECT/ZEBRA……………………………………………………………………

      97.        INSPECT/SECTION…………………………………………………………………

      98.        TOOLS/MEASURE…………………………………………………………………..

      99.        TOOLS/MATERIAL…………………………………………………………………

  100.        TOOLS/APPEARANCE……………………………………………………………..

  101.        TOOLS / ADJUST……………………………………………………………………

  102.        TOOLS / CLEAR……………………………………………………………………

  103.        TOOLS/ APPLICATION OPTIONS………………………………………………..

  104.        TOOLS/EXCHANGE APP MANAGER……………………………………………

  105.        MANAGE/PARAMETERS………………………………………………………….

  106.        MANAGE/Influenta tolerantelor asupra parametrilor……………………………

  107.        MANAGE/STYLE EDITOR…………………………………………………………

CAPITOLUL 11 – ANSAMBLU 3D – 2h 22’ 18”

  108.        RECAPITULAREA CAPITOLULUI ANTERIOR…………………………………

  109.        GET STARTED / LUNCH……………………………………………………………

a)      NEW…………………………………………………………………………………..

b)      OPEN………………………………………………………………………………….

c)      PROJECT……………………………………………………………………………..

d)      NEW PROJECT………………………………………………………………………

e)      CREARE DIRECTORI: LUCRU (Desene, Piese, Subansambluri), PIESE COMANDATE, PIESE STANDARDIZATE, TEMPLATE…………………………………………..

f)       EDITARE PROJECT…………………………………………………………………

1.      Workspace/LUCRU………………………………………………………………

2.      Libraries/ PIESE COMANDATE………………………………………………...

3.      Frequently Used Subfolders (../PIESE + DESENE + SUBANSAMBLURI)…..

4.      Folder options /Template (TEMPLATE) + Content Center Files (PIESE STANDARDIZATE)………………………………………………………………

g)      OPEN SEMPLE……………………………………………………………………….

  110.        GET STARTED / MY HOME………………………………………………………..

a)      HOME…………………………………………………………………………………

b)      TEAM WEB…………………………………………………………………………..

c)      TUTORIAL GALLERY………………………………………………………………

d)      LEARNING PATH……………………………………………………………………

  111.        GET STARTED / NEW FEATURES / WHAT’ NEW……………………………..

  112.        GET STARTED / HELP / HELP…………………………………………………….

  113.        NEW / METRIC / STANDARD.IAM………………………………………………..

  114.        APLICATIE – PROIECT NOU  ROBINET………………………………………..

CAPITOLUL 12 – ANSAMBLU 3D / CONSTRAIN 3D – 1h 39’ 32”

  115.        RECAPITULAREA CAPITOLULUI ANTERIOR………………………………

  116.        ASSEMBLE…………………………………………………………………………..

a)      COMPONENT...........................................................................................................

1.      PLACE……………………………………………………………………………

2.      PLACE FROM CONTENT CENTER……………………………………………

3.      IMPORT CAD FILES……………………………………………………………

4.      REPLACE………………………………………………………………………..

5.      MAKE LAYOUT…………………………………………………………………

6.      CREATE………………………………………………………………………….

b)      POSITION…………………………………………………………………………...

1.      FREE MOVE……………………………………………………………………..

2.      FREE ROTATE…………………………………………………………………..

3.      GRIP SNAP………………………………………………………………………

  117.        RELATIONSHIPS…………………………………………………………………...

a)      JOINT………………………………………………………………………………..

b)      CONSTRAIN………………………………………………………………………..

1.      ASSEMBLY- Mate, Angle, Tangent, Insert, Symmetry - (Aplicatie 1)………….

2.      MOTION. (Aplicatie 1)…………………………………………………………...

  118.        INSPECT/ANALYZE INTERFERENCE…………………………………………

  119.        INSPECT / ACTIVATE CONTACT SOLVER……………………………………

b)      CONSTRAIN………………………………………………………………………..

1.      TRANSITIONAL. (Aplicatie 2)…………………………………………………..

2.      CONSTRAINT SET. (Aplicatie 3)………………………………………………..

c)      SHOW..........................................................................................................................

d)      HIDE ALL…………………………………………………………………………..

e)      ASSEMBLE…………………………………………………………………………

  120.        PATTERN…………………………………………………………………………….

b)      PATTERN..................................................................................................................

c)      MIRROR....................................................................................................................

d)      COPY………………………………………………………………………………..

  121.        MANAGE.....................................................................................................................

b)      BILL OF MATERIAL………………………………………………………………

c)      PARAMETERS……………………………………………………………………..

  122.        FILE/SAVE AS…/PACK AND GO………………………………………………...

CAPITOLUL 13 – APLICATIE – PROIECT CLICHET – 1h 54’ 47”

  123.        RECAPITULAREA CAPITOLULUI ANTERIOR………………………………

  124.        PROIECTARE DE SUS IN JOS …………………………………………………..

  125.        APLICATIE – PROIECT CLICHET……………………………………………...

CAPITOLUL 14 – APLICATIE – DESEN DE ANSAMBLU – 1h 31’ 39”

  126.        RECAPITULAREA CAPITOLULUI ANTERIOR………………………………

  127.        NOTIUNI INTRODUCTIVE PENTRU PROIECT………………………………

  128.        APLICATIE – DESEN ANSAMBLU ROBINET CU BILA...................................

  129.        STYLE EDITOR / BALLOON (ISO)………………………………………………

  130.        STYLE EDITOR / PARTS LIST (ISO)…………………………………………….

  131.        PROIECTIE OVERLAY……………………………………………………………

  132.        EXPLODED VIEW – PRESENTATION…………………………………………..

  133.        APLICATIE – DESEN ANSAMBLU – CLICHET………………………………...

00’ 00”

14’ 20”

15’ 40”

22’ 00”

29’ 00”

32’ 00”

34’ 00”

43’ 00”

00’ 00”

03’ 20”

04’ 30”

04’ 30”

19’ 20”

22’ 00”

24’ 19”

27’ 20”

32’ 44”

35’ 10”

38’ 00”

38’ 40”

39’ 55”

40’ 32”

41’ 50”

42’ 18”

45’ 40”

47’ 15”

47’ 45”

49’ 09”

50’ 21”

53’ 00”

54’ 33”

56’ 00”

56’ 48”

59’ 10”

00’ 00”

04’ 02”

04’ 09”

08’ 14”

11’ 21”

12’ 43”

12’ 43”

15’ 45”

16’ 33”

17’ 35”

24’ 09”

31’ 21”

34’ 18”

36’ 47”

38’ 08”

41’ 40”

42’ 32”

42’ 32”

43’ 25”

47’ 54”

49’ 20”

50’ 42”

56’ 32”

1h 02’ 20”

1h 03’ 20”

1h 05’ 30”

1h 06’ 30”

1h 09’ 40”

1h 09’ 30”

1h 09’ 40”

1h 09’ 50”

1h 11’ 00”

1h 12’ 12”

1h 12’ 12”

1h 13’ 10”

1h 13’ 30”

1h 13’ 30”

1h 15’ 10”

0’ 00”

04’ 35”

5’ 44”

35’ 00”

46’ 38”

51’ 16”

57’ 15”

59’ 50”

1h 03’ 50”

1h 12’ 10”

1h 19’ 20”

1h 21’ 40”

1h 25’ 40”

0’ 00”

06’ 20”

06’ 30”

31’ 05”

42’ 50”

48’ 27”

52’ 15”

58’ 13”

1h 00’ 34”

1h 05’ 03”

1h 08’ 15”

1h 11’ 15”

1h 18’ 40”

1h 21’ 20”

1h 24’ 00”

1h 29’ 20”

1h 32’ 00”

0’ 00”

4’ 13”

04’ 13”

04’ 13”

06’ 50”

08’ 25”

09’ 47”

10’ 21”

11’ 25”

12’ 32”

13’ 55”

15’ 38”

16’ 25”

16’ 25”

17’ 01”

17’ 30”

19’ 01”

19’ 18”

19’ 32”

20’ 16”

20’ 43”

21’ 18”

21’ 18”

21’ 40”

22’ 20”

23’ 00”

23’ 53”

24’ 25”

25’ 44”

26’ 38”

27’ 00”

28’ 51”

30’ 06”

31’ 22”

32’ 50”

34’ 06”

35’ 48”

35’ 48”

42’ 40”

47’ 25”

49’ 42”

51’ 10”

00’ 00”

04’ 20”

08’ 08”

21’ 00”

21’ 40”

23’ 00”

36’ 40”

43’ 00”

44’ 10”

46’ 50”

47’ 28”

1h 03’ 53”

1h 04’ 10”

1h 04’ 53”

1h 07’ 05”

1h 13’ 00”

1h 15’ 04”

1h 16’ 13”

1h 16’ 36”

1h 17’ 07”

1h 18’ 25”

1h 18’ 25”

1h19’ 29”

1h 20’ 05”

1h 20’ 50”

1h 21’ 23”

1h 22’ 45”

1h 24’ 16”

1h 24’ 35”

1h 24’ 50”

1h 27’ 20”

00’ 00”

06’ 15”

11’ 40”

13’ 23”

13’ 55”

14’ 00”

14’ 05”

14’ 34”

16’ 40”

24’ 15”

24’ 50”

30’ 30”

32’ 15”

43’ 40”

49’ 00”

1h 09’ 00”

1h 11’ 23”

00’ 00”

07’ 04”

07’ 04”

07’ 09”

17’ 35”

18’ 58”

22’ 04”

28’ 32”

36’ 12”

43’ 21”

43’ 57”

48’ 11”

51’ 43”

55’ 20”

56’ 17”

56’ 25”

57’ 10”

57’ 15”

57’ 30”

58’ 10”

58’ 20”

59’ 40”

1h 05’ 30”

1h 05’ 50”

1h 09’ 43”

1h 16’ 55”

1h 18’ 20”

1h 19’ 17”

1h 20’ 20”

1h 20’ 30”

1h 21’ 10”

1h 23’ 20”

1h 23’ 25”

1h 23’ 46”

1h 23’ 51”

1h 24’ 50”

1h 26’ 00”

1h 26’ 16”

1h 26’ 58”

1h 27’ 42”

1h 27’ 44”

1h 31’ 32”

1h 32’ 44”

1h 35’ 40”

1h 37’ 40”

1h 38’ 36”

1h 41’ 00”

1h 42’ 18”

1h 42’ 35”

1h 42’ 49”

1h 45’ 09”

1h 47’ 08”

1h 50’ 00”

1h 50’ 10”

1h 50’ 24”

1h 51’ 11”

1h 54’ 27”

1h 56’ 42”

1h 57’ 02”

1h 57’ 30”

00’ 00”

05’ 06”

13’ 21”

33’ 22”

35’ 42”

39’ 40”

47’ 10”

47’ 42”

50’ 42”

52’ 00”

52’ 21”

53’ 01”

53’ 28”

54’ 45”

1h 02’ 37”

1h 03’ 36”

1h 04’ 57”

1h 07’ 03”

1h 09’ 20”

1h 10’ 52”

1h 12’ 22”

1h 29’ 42”

1h 29’ 55”

1h 32’ 10”

1h 32’ 46”

1h 39’ 18”

1h 40’ 48”

1h 47’ 41”

1h 58’ 50”

00’ 00”

04’ 10”

04’ 23”

05’ 14”

05’ 27”

06’ 31”

08’ 40”

12’ 00”

12’ 05”

13’ 09”

14’ 00”

17’ 45”

21’ 23”

22’ 01”

22’ 01”

22’ 14”

22’ 21”

23’ 12”

23’ 31”

24’ 20”

24’ 35”

25’ 52”

00’ 00”

04’ 03”

04’ 48”

04’ 48”

07’ 06”

14’ 03”

15’ 57”

17’ 10”

18’ 11”

21’ 50”

22’ 18”

22’ 20”

23’ 03”

25’ 04”

25’ 04”

33’ 23”

33’ 35”

51’ 46”

1h 00’ 45”

1h 01’ 46”

1h 05’ 00”

1h 05’ 13”

1h 13’ 40”

1h 20’ 17”

1h 20’ 30”

1h 22’ 22”

1h 24’ 20”

1h 24’ 28”

1h 28’ 27”

1h 30’ 00”

1h 31’ 00”

1h 31”05”

1h 32’ 31”

1h 34’ 20”

00’ 00”

04’ 15”

41’ 47”

00’ 00”

04’ 36”

08’ 34”

28’ 41”

31’ 36”

51’ 20”

58’ 56”

1h 03’ 57”

TOTAL:

25h 27”